Forum Post: MSP430FR6047: USS water flow Temperature
Part Number: MSP430FR6047 Tool/software: I am trying to building a water meter sensor using the MSP30FR6047EVM and USS library. And I need to extract the temperature calculation result from...
View ArticleForum Post: RE: MSP430FR2476: ADC measurement in LPM3 for lowest power...
Hi Burak, I believe Bruce's comments are a pretty good advice. Does it help with your inquiries? Best Regards, Diego Abad
View ArticleForum Post: RE: MSP430F2274: RX interrupts collisions
Hi Geral, I would recommend to disable a COMM once the other is active, and vice versa. Best Regards, Diego Abad
View ArticleForum Post: RE: EVM430-FR6043: No Image to load on the board at the intended...
I have captured a a screen shot to get all entire cycle. Given the larger time window you the vertical scale is zoomed out. I think it looks very similar to the snap shot you shared. You can also see...
View ArticleForum Post: RE: MSP430F2274: RX interrupts collisions
I expect that if the two are independent then it should work. But if servicing one requires doing something to the other, then there could be problems. The cure being highly dependent on the...
View ArticleForum Post: RE: MSP430FR2532: warning during compilation: output section...
Hi Mr. Abad, I just tried to compile the project in CCS v20.3.0, either let compiler fall back to v21.6.1 and explicitly choose it. I was able to successfully compile and then load the binary image...
View ArticleForum Post: MSP430G2744: The values 0x10F0-0x10FF in Segment A become 0xFF...
Part Number: MSP430G2744 Other Parts Discussed in Thread: UNIFLASH Tool/software: Hi experts, We're currently investigating an issue very similar to the one in the original thread . After mounting the...
View ArticleForum Post: RE: MSP430FR2476: ADC measurement in LPM3 for lowest power...
Yes, it was helpful, thank you.
View ArticleForum Post: RE: MSP430FR6047: USS water flow Temperature
Hi Toby, Have you tried don't change anything to read the temperature value? Will loop more expert to comments. Thanks! Best Regards Johnson
View ArticleForum Post: RE: MSP430FR6047: ADC capture data using the Get Pointer method
Hi Toby, Thus any questions here? To be honest, it will very difficult to debug and monitor ADC waveform if no USB/HID Bridge... We will still recommend connect to USS design center to monitor...
View ArticleForum Post: RE: MSP430FR6047: ADC capture data using the Get Pointer method
Yes, I have that board, but I also have a board that I designed. I want to verify that the board that I designed is working correctly on the ADC capture from the transducers. And yes, is there a way to...
View ArticleForum Post: RE: MSP430FR6047: USS water flow Temperature
Yes I have and here is the output for the configuration with no changes to the USS_userConfig.h header file: AbsTof_UPS, 5.4351e-05 AbsTof_DNS, 5.4352e-05 DToF, -1.1509e-09 VOL_FR, -4.9639e+00...
View ArticleForum Post: RE: MSP430FR2532: warning during compilation: output section...
Hi ZL, I found this E2E thread that should explain a little in detail on what this error means . Best Regards, Diego Abad
View ArticleForum Post: RE: MSP430G2744: The values 0x10F0-0x10FF in Segment A become...
Hi O.H, The area that you are trying to modify in the information memory area. Normally, this area should be left alone unless there's a good understanding of how to modify the values here. 1. I...
View ArticleForum Post: RE: MSP430FR2532: warning during compilation: output section...
Hi Mr. Abad, The closest to _nop() in our code base is __delay_cycles(). But I am still getting the warning message after commenting out those lines of __delay_cycles(). My question is, should I be...
View ArticleForum Post: RE: MSP430FR2532: warning during compilation: output section...
Hi ZL, The error itself shouldn't generate an issue since it only mentions that compression is not happening. Maybe modifying the linker file could help, but I don't think should affect functionality....
View ArticleForum Post: RE: MSP430FR2532: warning during compilation: output section...
Hi Mr. Abad, Since I have your attention, could you please explain why CCS v12.8 failed to compile with TI v21.6.1 compiler? This is what alarmed me. I can live with the warning message as long as it...
View ArticleForum Post: RE: MSP430G2744: The values 0x10F0-0x10FF in Segment A become...
Hi Diego Abad Thank you for your supports. [quote userid="565794"...
View ArticleForum Post: RE: MSP430FR6047: PIN number 74
Hi Harsh, My apologies for the late reply. Even when disabling the LCD (disabling all references) there may be minimal leakage. From what I can see, the main reason for connecting this pin to ground is...
View ArticleForum Post: RE: LP-MSPM0L2228: clock is not accurate when enabling FCL
Helic, I mount the new sample on evm. The samples are the ic which i just apply and got. ID ( 41C40004h): 1BB9F02F not enable ROSC, FCL enable ROSC: enable ROSC+FCL. if enabling FCL, it still becomes...
View Article