Forum Post: RE: MSP430G2553IRHB32R Debug issues
Hello Itay, How are you connecting J1 to the MSP-FET ? Are you connecting to the correct pin on the FET for your power scheme?
View ArticleForum Post: RE: MSP432 where is the correct definition of flashmailbox ??
Hello Jean, We are looking into this matter and should give you an answer shortly. Thank you for pointing out an inconsistency in the documentation here.
View ArticleForum Post: RE: Confusion on Revised Pulsoximeter Design Using the MSP430...
Hello Fan, Please see the DAC12 Section within the MSP430FG437 User Guide for information on how the DAC12 module works and how to use it. For more information on how DACs operate and basics, please...
View ArticleForum Post: RE: Connect MSP430i2040 with Adafruit Huzzah 8266
Hi Alaa, It's been a couple weeks since we've last heard from you so I'll be closing out the thread. If you have any other questions, let us know and we can reopen the thread, otherwise, please hit...
View ArticleForum Post: RE: MSP430G2553IRHB32R Debug issues
Hi, I'm connecting J1 as following: J1.1 [VSYS] --> MSP-FET .2 [VCC_TOOL] J1.2 [SBWTDIO/RST] --> MSP-FET .1 [TDO/TDI] J1.3 [SBWTCK] --> MSP-FET .7 [TCK] J1.4 [GND] --> MSP-FET .9 [GND]...
View ArticleForum Post: RE: EVM of MSP430F677x three-phase meter
Hi Tamir, Take a look at Figure 2 (also shown below) in the Implementation of a Single-Phase Electronic Watt-Hour Meter Using the MSP430F6736(A) app note. It shows a 1-phase 2-wire star configuration...
View ArticleForum Post: Verify MTBF and FIT example calculation
Greetings, I am posting this question against the MSP430FR5969 but its applicability is general to all TI silicon devices. I am requesting a confirmation of the calculation below. In this example we...
View ArticleForum Post: RE: EVM430-F6779 cover
Hi Kyle, I couldn't find a cover in the TI Store and didn't see it mentioned in our documentation. I'll check with our experts to see if one exists. Regards, James MSP Customer Applications
View ArticleForum Post: RE: MSP432 to MSP432 I2C Master read
Stefan, Is this still an open issue, or is your fix acceptable? I have a feeling it has to do with the timing of the stop bit in conjunction with repeated start. Best regards, Cameron
View ArticleForum Post: RE: MSP430F2272 Update
Vincent, Is flashing FW B by JTAG an acceptable solution for you, or do you still need assistance here? Best regards, Cameron
View ArticleForum Post: RE: SLAA361 (audio codec) simulation help needed
Mich, Let us now if you're able to get this value to work.
View ArticleForum Post: RE: MSP-GANG DLL SBW Issue
Chris, I tried emailing you. Are you able to convert your project to Labview 8 and send it to us?
View ArticleForum Post: RE: CapTIvate - Filtering and latency of position data for slider
Hi Mike-san, Thank you very much for your reply. I understood! Regards, Yuji
View ArticleForum Post: RE: CapTIvate - Metal-touch and static electriscity
Thank you Dennis! I read it but unfortunately, I could't find out that the mention about static electricity and metal touch.. Did you reach it? Regards, Yuji
View ArticleForum Post: RE: MSP430G2553IRHB32R Debug issues
Hi, There is not other power source connected to the target. Only the MSP-FET . I'm not using the fuse blow functionality so following the user manual, I should not connect TEST/VPP to TEST/SBWTCK and...
View ArticleForum Post: RE: MSP430G2553IRHB32R Debug issues
[quote user="Itay Cohen67"]Any other ideas?[/quote]The error messages you are getting suggest the SBW communication is intermittent, rather than completely dead. Some suggestions: In the Target...
View ArticleForum Post: RE: MSP430 problem with reading from UART when NOT debugging...
Also, can you please attach more of your code here as well as any related .h or .c files? I'm having a hard time understanding where and how your two code sections above are used (such as in main(),...
View ArticleForum Post: RE: Verify MTBF and FIT example calculation
Kevin, Are all 19000 devices to be operating for 30 years?
View ArticleForum Post: RE: Verify MTBF and FIT example calculation
Hi Cameron, Yes. In the example it is assumed that all 19000 units begin operating at the same time and those units which do not fail run continuously for 30 years. Thanks, Kevin
View ArticleForum Post: RE: PMM_setVCore(PMM_CORE_LEVEL_2) gets stuck
Atif, To rule out IAR as the issue here, can you please try running the CCS example? Regards, James MSP Customer Applications
View Article