Forum Post: RE: What effects does debug under CCSv5 with SBW connections have...
I have in the past used breakpoints, but not recently in the presence of this debug problem. The device acts up immediately upon clicking Debug's Run button, and I've concentrated on 'scoping the Tx...
View ArticleForum Post: MSP430F2619 - Disabling CPU causes 32kHz Crystal to drop out
Hi All, I am trying to use LPM2 with my application and I am having some trouble with my 32 kHz crystal. In my setup I am using the DCO to drive MCLK, and SMCLK at 16 MHz. I am using my 32 kHz crystal...
View ArticleForum Post: RE: MSP430F2619 - Disabling CPU causes 32kHz Crystal to drop out
Edit**** a 16.138 kHz timer
View ArticleForum Post: RE: MSP432 Maincode debugging with a Bootloader loaded
Thanks for the detailed feedback. After looking at Section 8.2.4 Flash Erase in the Technical Reference Manual (TRM), I remembered that the smallest amount of flash that can be erased in both Main and...
View ArticleForum Post: Getting started with the MSP-EXP430G2
Hello I recently purchased a MSP-EXP430G2 Launchpad. I have been using CCS V6.1.1 with the F28M36. I need a simpler chip for my current projects and the MSP430 seems to meet my needs and allows me to...
View ArticleForum Post: RE: Trying to use channel 0 and channel 1 of SD24 atod converter
You can close this item. Steve
View ArticleForum Post: RE: Getting started with the MSP-EXP430G2
Ryan, I do not recall getting prompted for an update. The MSP Emulator I have is version 6.0.1.8. I will perform a uninstall and reinstall CCS today and see what happens. Galen
View ArticleForum Post: RE: Getting started with the MSP-EXP430G2
Galen, Typically an emulator firmware update is required when using an IDE + FET tool for the first time. My current Emulator package is 6.3.4.4, the version you are using is quite old and could be...
View ArticleForum Post: RE: Emulator for MSP430F5324
The eZ-FET lite found on the MSP-EXP430F5529LP supports all programmable MSP430 devices including the MSP430F5324 . It is possible to use the Vcc, GND, RST, and TEST pins on the eZ-FET lite portion of...
View ArticleForum Post: RE: MSP432 COMP C1.0 input at Vcc
Roman, No problem on the formatting, it just gets faster responses when you use t :-) Good to hear you found the issue. Do you know how the port became blown? (I always have extra parts on hand for my...
View ArticleForum Post: RE: After building , running the code on MSP432P401R gives error.
Hi Andrew, Could you please run the factory reset as described in www.ti.com/.../slau597 chapter 5 FAQ?? Thanks, David
View ArticleForum Post: RE: MSP432 - Trying to Erase the Sector 0 Bank 0 before Writing...
Hi Prem, Is this debug effort still ongoing? If not I will close out this thread. Please let us know. David
View ArticleForum Post: RE: MSP432 LaunchPad V2 with EDUMKII running Keil uvision V5.20...
I've compared files between the ccs and keil projects: all grlib (17 files) identical all driverlib (58 files) identical all lcddriver (4 files) identical the keil project has a RTE_Components.h which...
View ArticleForum Post: RE: Getting started with the MSP-EXP430G2
Ryan, I just uninstalled and reinstalled CCS version 6.1.3.00034. My MSP Emulators and Device Support Files are Version 6.3.4.4. I am getting the same error as before: Failed to load program... Cannot...
View ArticleForum Post: Old code does not compile with latest CCS and MSPWare versions...
Hello, I am a teaching assistant for a course in which we use the TI MSP432P401R LaunchPad at the Georgia Institute of Technology, Atlanta GA. Back in January 2016, when I took the course, we used CCS...
View ArticleForum Post: RE: Getting started with the MSP-EXP430G2
Galen, Can you try using an IDE other than CCS (IAR, Energia , Pro-FET430, etc.) and see if any of these report a similar issue? We are trying to isolate the issue between the hardware or software....
View ArticleForum Post: RE: Getting started with the MSP-EXP430G2
Ryan, I will do that. On a separate PC that has Windows 10 I can connect using the CCS Cloud IDE. I checked the driver between the 2 PC and it is the same one which I guess you knew cause the date is...
View ArticleForum Post: RE: Trouble with Debug mode MSP430G2231 - Debug is start in...
Alexander, I have a couple questions. First, can you post/send me your asm file? Second, which FET are you using?
View ArticleForum Post: Getting started with wlan station - MSP430FR6989
hi all, I've been trying to use the getting started with wlan station code for a couple of weeks now. I have an MSP430FR6989 and a CC3100 wifi booster pack. Is there a board.h and board.c file...
View Article