Forum Post: CC430 Port 3, 4, 5 interrupt vector?
Hi, Aren't port 3, 4 and 5 capable of interrupts? I couldn't find their interrupt vectors on interrupt vector table. Thanks
View ArticleForum Post: USB Update Fails using El Capitan and HUB
Our msp430f5528 based product firmware update functionality has stopped working on Mac OSX El Capitan when device is attached to a hub. My investigation has revealed that re-enumeration of a USB device...
View ArticleForum Post: RE: MSP432 Timer CCR0 interrupt question
Yes, you are correct. Historically, 16-bit MSP430, this was not the case. The IFG to TAxCCR0 was automatically cleared when the ISR was serviced ( www.ti.com/.../slau144j.pdf ). You must clear the IFG...
View ArticleForum Post: MSP430 display via I2C - how to initialize the display and write...
So, I have a MSP430G2553 connected via I2C to a display with PCF8574 extender. I am unable to successfully initialize + write something on the display (checked lots of tutorials). I found how to clear...
View ArticleForum Post: RE: when i use MSP432Ware_3_50_00_02 , i wantto use the examples...
Hello, Which version of CCS are you using? This thread is not directly applicable but are there any potential issues with the installation or directory properties/permissions? e2e.ti.com/.../1491527...
View ArticleForum Post: RE: MSP430FR5989 / MSP430FR5986. Recording Problems
Hi Jose, By "recording" do you mean programming? Unknown device is usually a JTAG communication issue. This is most often resolved to an issue with the power supply or JTAG lines. Is this on...
View ArticleForum Post: RE: Help me please
Hi user4811616, We don't typical develop code for you. Have you tried looking at our example code? From the sound of it, you will likely want to check out the I2C and/or SPI examples, along with UART...
View ArticleForum Post: RE: when i use MSP432Ware_3_50_00_02 , i wantto use the examples...
hello , i using win7 32 ccsv6, i installed it on the c:\ti , when i changed the properties about all the files became r/w , it 's the same bad !
View ArticleForum Post: RE: Which OS versions do MSP-GANG-Programmer support?
Thank you for your reply. The purpose of updating the development environment this time is this time. Regards, Da
View ArticleForum Post: RE: Which OS versions do MSP-GANG-Programmer support?
Thank you for answering. Please update the document and the website. Regards, Da
View ArticleForum Post: RE: MSP-EXP432P401R _ 's external oscillatorproduce Low clock...
yes , it's launchpad ! the code i used msp432_ware example . it's msp432p401x_cs_06
View ArticleForum Post: RE: visible light communication
[quote user="Clemens Ladisch"]What does this have to do with the MSP430? A photodiode needs some amplification. Show the entire circuit. [/quote] am not using controller..Just to test the photodiode..
View ArticleForum Post: RE: 800 spectral lines out of 1024 FFT outputs
Hi Brent, Thanks for your response. please go through the below details we need help. Brief Details of our work: To the MSP ADC14 we fed a (0-0.625volt) peak to peak sine signal. The sine signal is...
View ArticleForum Post: RE: want to interface ultrasonic with msp430g2553
ultrasonic sensor HC sr-04, actually i am working on Vissim embedded software on that i want to design a simple robot which can detect a threshold distance . first i generate 10 usec pulse so that i...
View ArticleForum Post: RE: want to interface ultrasonic with msp430g2553
i have set the launch pad on 1MHZ , divide by 1 , aclk . set the TACTL at 12C and TACCTL0 on capture on rising edge ,CCIS0 , CAP enable , interrupt enable . when the Echo on rising edge measure the...
View ArticleForum Post: RE: MSP432 eUSCI_B3 confusion
I was having some difficulty getting the I2C on P6 to work on our board, so I decided to eliminate some variables and use a MSP-TS432PZ100 development board. I parameterized my code to work with any of...
View ArticleForum Post: What can cause exceptions when running MSP432 RTOS?
Hello, everyone! I am using MSP432 RTOS(tirtos_msp43x_2_16_01_14) to develop my application in CCSv6.1.3. When running my code of RTOS, a exception must occur. Who can tell me what cause a exception...
View Article