Forum Post: RE: Wakeup time from LPM0 and LPM1
KoT, I can try to trigger it but cannot promise that it will realized quickly because this would mean to update ALL 5xx/6xx datasheets. In the end as you also noted it is somehow mentioned in the...
View ArticleForum Post: RE: MSP430FR2311: Correct way to reset SPI slave state machine
Hi Richard. In an application like yours I did exactly the same, one pin was a "chip select" pin that was controlled by the master MSP430. Whenever it was driven high, I reseted the USCI module by...
View ArticleForum Post: RE: Wakeup time from LPM0 and LPM1
Dietmar, Yes. I will try to close this item with my customer. Please try to put this information in datasheet. I put this item closed for now. Thanks and regards, KoT
View ArticleForum Post: RE: Security and update tool
Hi Dan, So, what I saw from your firmware is that you have two parts: Part 1. @2000 has 56083 bytes Part 2. @1b078 has 10883 bytes I still need to know some other parameters. these two parts firmware...
View ArticleForum Post: RE: MSP432P401M: MSP432 Development Platform in EZ form factor
What exactly do you mean with "EZ form factor"? Many LaunchPads have the eZ-FET (lite) emulator. If you mean a small USB stick like the EZ430-F2013 : that one uses a very small MCU chip with very few...
View ArticleForum Post: RE: MSP430FR2311: Correct way to reset SPI slave state machine
Section 22.3.1 of the User's Guide says: When set, the UCSWRST bit resets the UCRXIE, UCTXIE, UCRXIFG, UCOE, and UCFE bits, and sets the UCTXIFG flag.
View ArticleForum Post: MSP wakeup from power down
Hi Champs, Can you give a recommendation for the following requirements: - What is the device with the fastest wakeup from power down? - What is the device with the lowest startup current after power...
View ArticleForum Post: RE: MSP432P401M: MSP432 Development Platform in EZ form factor
[quote user="Wil Blake"] Part Number: MSP432P401M Does TI anticipate an MSP432 Development platform arriving using the EZ Form Factor? [/quote] Don't know about TI, but you can build by yourself...
View ArticleForum Post: RE: Security and update tool
Fatma, Thanks for the response. I must apologize. The code in Part 2 @1b078 should not be in the file. I errored. I'm sure that's what caused the app to crash. To answer your other questions, we...
View ArticleForum Post: RE: MSP430FR5847: Problem with switching MSP430FR5847 to 16 MHz...
thanks! I'm new to FRAM chips... Shall I lock control register (FRCTL0_H = 0) after? PS maybe it is worth to add a small note in slau367l.pdf, under table 3-5 (CSCTL1 Register Description) that if you...
View ArticleForum Post: MSP430FR5989: Confirm the layout guide line for VQFN package.
Part Number: MSP430FR5989 Hi TI Experts, Please let me confirm the following question. [Question] According to the data sheet, there are some thermal pad and via under the device. Do we must follow...
View ArticleForum Post: RE: MSP430FR5989: Confirm the layout guide line for VQFN package.
Hi Kaka! The pad recommendations at the end of the datasheet are for the packages in general - in your case for the RGC package. It shows 25 vias in the thermal pad. The MSP430 is a very low power...
View ArticleForum Post: RE: MSP430F5435a - reset cause
Hello Ryan, did you have time to see with the design team the purpose of a 0x1CV value in SYSRSTIV ? Thank you for your help Regards,
View ArticleForum Post: RE: rtc
Hi, Anderson i go through that that pdf suggested by,but i found problem while adding header file. It gives me such kind of error. Description Resource Path Location Type #10010 errors encountered...
View ArticleForum Post: RE: MSP430G2744: Restarting the MSP430 periodically
What do you mean with "restart"? A wake-up triggered by an interrupt, or a complete reset? (Both should work.)
View ArticleForum Post: RE: Security and update tool
Hi Dan, no problem at all. it is a good catch. i need to improve so the program shows the error message. I'll address this as the enhancement. the length actually has to be multiples of 0x1000 byte. I...
View ArticleForum Post: RE: MSP430FR5989: Confirm the layout guide line for VQFN package.
Hi Dennis, Thank you for your advice. I got it. Best regards. Kaka
View ArticleForum Post: RE: MSP432P401R: Any reference design or app not for interfacing...
Hi Randhir, in case you are referring to PHY chips for communication via Ethernet, then the easyweb ( www.ti.com/.../slaa137a.pdf) with the MSP430 & CS8900A is the closest I know of (I am however...
View ArticleForum Post: Using XDS100 v2 for programming MSP432 series
I am developing a board based on the MSP432 and the reference design uses the FET emulator. I already have the XDS100v2 since I used to work with C2000 but I was wondering if anyone else has used this...
View ArticleForum Post: MSP430F1232: EEPROM Endurance for high electro-maganetic field
Part Number: MSP430F1232 We are using MPS430 for RFID reader controller. Could you let me know whether the EEPROM is affected (garble of the read data) in the high electro-magnetic field? Best regards,...
View Article