Forum Post: RE: Reset is not stable, MCU is not power up normally
ONE OF THE REPUTED SUPPLIER ASKED ME TO POST TO THIS .I have tried through local TI engineer and generally it does lead NOT to resolution.I have many an experience in the past
View ArticleForum Post: RE: Reset is not stable, MCU is not power up normally
An E2E forum is for communication and exchange between CUSTOMERS, and not a TI support hotline. Ti staff -might- be present. As others stated, get to TI directly, e.g. via FAE. And don't hijack threads.
View ArticleForum Post: RE: Comparison between 32 bit int, float and 64 bit int...
[quote user="f. m."] And there is an ongoing discussion in many circles if those in power are actual humans. Again digressed quite far, no link to 32-bit / 64-bit calculations ... [/quote] I wanted to...
View ArticleForum Post: RE: Reset is not stable, MCU is not power up normally
Shouting in UPPERCASE and flooding will not help you get attention you are looking for. At least not mine. Yes, im done here in this thread
View ArticleForum Post: RE: Comparison between 32 bit int, float and 64 bit int...
[quote]I wanted to stop,...[/quote] Me too, but just can't resist ... [quote] ...the success of Pokémon Go, ... [/quote] Probably doesn't mean the many people that have themselves "nominated for the...
View ArticleForum Post: RE: Reset is not stable, MCU is not power up normally
While I do not know who you are, I DO NOT NEED YOUR ADVICE or as you are imagining your attention.Obviously you are not reading the technical aspects of an issue, before letting your wisdom to flow in...
View ArticleForum Post: RE: MSP430F5338 setting
Hi Sathya! Have a look in the User's Guide , chapter 5. UCSCTL4 configures the sources for the internal clocks. In addition, UCSCTL5 gives you some dividers for the clocks. For using an external clock...
View ArticleForum Post: RE: EVM430-F6779
Thank you! for the calibration, I have discoverd by logging the rs232 communication that the calibration.exe calculate the calibration value and because of the -100% it was set to zero's. Finally I...
View ArticleForum Post: RE: Port Damage I2C MSP430G2553
> There is NO hot plugging going on. Sure. People do not make mistakes and if they do - they always tell you. And all the wiring and connectors do not fail, ever. :D This could be the case of GND...
View ArticleForum Post: RE: 20nH-200nH range inductance tester
Thank you, f.m., I also saw in the Internet PWM-based solution. I am also not an analog-inductor-guy, because I don't have specific tests equipment for 100MHz-1000MHz range, which could cost me...
View ArticleForum Post: RE: 20nH-200nH range inductance tester
I don't know the measuring range of this LCR meter, but I had this link saved in my bookmarks: Maybe it is interesting for you.
View ArticleForum Post: RE: 20nH-200nH range inductance tester
Thank you, Dennis, but this solution has 10kHz ceiling point.
View ArticleForum Post: RE: 20nH-200nH range inductance tester
[quote]I am also not an analog-inductor-guy, because I don't have specific tests equipment for 100MHz-1000MHz range, ...[/quote] With proper selection of the "other" element(s) of the resonant circuit...
View ArticleForum Post: RE: 20nH-200nH range inductance tester
[quote user="f. m."] I'm quite sure there are DVMs around with C/L measuring capability[/quote] You are right, but DVMs has 1mH lowest ceiling point it is 100000 times far away from what I need.
View ArticleForum Post: RE: 20nH-200nH range inductance tester
[quote]You are right, but DVMs has 1mH lowest ceiling point it is 100000 times far away from what I need.[/quote] I remember DVMs going down at least to the uH range. One might expect some correlation...
View ArticleForum Post: RE: 20nH-200nH range inductance tester
[quote user="f. m."]One might expect some correlation between range and price ...[/quote] No, the range is quite tight: 20nH-200nH. So this is very narrow, but working frequencies for measurements are...
View ArticleForum Post: code dumping using cc debugger
I developed my own custom board using CC2541 but i have less no. of GPIO pins so my issue is i want to reuse debug pins for dumping code through CC debugger. Is there any other way to dump code without...
View ArticleForum Post: RE: 20nH-200nH range inductance tester
[quote]No, the range is quite tight: 20nH-200nH. So this is very narrow, but working frequencies for measurements are quite high.[/quote] You are right - such small coils would require large capacitors...
View ArticleForum Post: How to link an unused function in C with CCSv6 and cl430 compiler
Hello all! I am working a project in CCS_V6, with cl430 as compiler and MSP430F5438A I'm looking for an instruction which enable to me to link an unused function. In fact, I need to use the code of my...
View ArticleForum Post: RE: Launch Pad Board Sequence Question
What does "perfectly timed" mean? How many picoseconds of deviation can you tolerate?
View Article