Forum Post: RE: Problem with Auto Addressing in MSP430 DALI stack(MSP430G2553)
Dear Subrahmanya, I would suspect that the issue might be related to the random address generation. If you look into the special functions you will see that the ‘random-ness’ is determined by the DCO...
View ArticleForum Post: RE: LSM9DS1 Library for MSP430F5xxx
Thanks Brian, Thanks Ryan. 1/ @Brian: My Environment is CCS v5.5. unfortunately, I see that Energia still very limited as a project environment compared to CCS/IAR. 2/ @Ryan: I see your point and I...
View ArticleForum Post: RE: LSM9DS1 Library for MSP430F5xxx
Delared, Energia is programming for the novice hobbyist, certainly not a tool for the professional programmer. I brought it up because a lot of times you can't tell which bin the original poster...
View ArticleForum Post: RE: MSP430F5528 rev. F issue with JTAG - doesn't work
[quote user="Valery Alexeev"] 2. Could it be the case that purchased F5528 rev. F items are fake? According to the marking on the chips rev. F is produced later than rev. I (rev. F is 2014 year while...
View ArticleForum Post: RE: RFID Card Reader UART to MSP430g2553
Sorry, I don't have any clue. The problem with RFID is that there is no real standard. The term 'RFID' simply means that somehow some information of some kind is read from a tag through RF. There are...
View ArticleForum Post: RE: How to build a Look Up Table with CCS 6.2 assembly code?
Hi Antony, Which MSP430 are you trying to run the code on and what problems are you seeing with it? Best regards, Caleb Overbay
View ArticleForum Post: RE: RFID Card Reader UART to MSP430g2553
And, well, for the exact meaning of the reader output, consult the reader manual. Ask the manufacturer for detail information - I had lots of trouble with this too, until I found someone who did...
View ArticleForum Post: RE: CCS reporting incorrect variable types in VARIABLE window
This has not been consistent across different machines and versions of CCS. I have seen this also get reported in the VARIABLES window as unsigned ints with values of 40,000 (positive) and 34,464 (also...
View ArticleForum Post: RE: CapTIvate METAL TOUCH and thermal expansion
Hi Yuji, Yes, if the space between the metal overlay and the sensor electrode underneath the overlay changes due to mechanical stress caused by elevated temperatures, then this will be detected in by...
View ArticleForum Post: RE: LCD Libraries
You may also want to take a look at forum.43oh.com and do a search on LCD, 16x2, etc
View ArticleForum Post: RE: CC430F5133 power consumption problem in LPM3 or LPM4 mode
Hi Ryan, Thank you very much! The power consumption problem has been solved with your kind help. Before going to LPM3 mode, what I did is as below . The power consumption is 4uA in LPM3. * UCSCTL6 =...
View ArticleForum Post: RE: Programming blues
O.K. Let's think about that. Currently the booster has a 1pF cap across RST to ground, merely to take the edge off the reset signal coming off a TACT switch. If I want to continue being careful about...
View ArticleForum Post: RE: Programming blues
A current measurement of the power rail at the USB connector ought to be informative. At that point both regulators are drawing off the bus supplies from the USB V+ and V- pins and quiescent current...
View ArticleForum Post: RE: Programming blues
The F5529-LP already has a mechanical switch S3, a pull-up resistor R27, and a capacitor C17 on the RST signal. What is on your Booster could be the last straw. Try disconnect RST from your Booster...
View ArticleForum Post: RE: MSP430FR5859 Hangs when using I2C in slave mode and a timer
Here's a curiosity: The errata sheet (SLAS457J) lists ----------------------------------- PMM24: Device may enter lockup state during wake-up from LPM3 and LPM4 The device may enter a lockup state...
View ArticleForum Post: RE: Breakpoints in GDB with MSP432P401R board
Any updates on this? Im having the same exact issue.
View ArticleForum Post: MSP430F2618 opt_for_speed setting changes __delay_cycles() duration
I have an MSP430F2618 executing at 16MHz. As part of my initialization sequence, I would like to debounce a signal that is on a noisy line and susceptible to transient value changes. To help with this,...
View Article