Forum Post: RE: 16*2 lcd connect with msp430fr4133
You should google for MSP430 in combination with HD44780. Since this might be everyone's first display you should find a lot of material. Maybe also search for HD44780 only - there might be more...
View ArticleForum Post: RE: msp430g2553 SPI adxl362
Hi Edgard! I do not have an example for the ADXL362, but SPI is very simple and to get started I would recommend to have a look at the code examples for the MSP430G2553 . Dennis
View ArticleForum Post: RE: When will EXP-MSP432P401R LaunchPads ship with MSP432P401R...
[quote user="Eric Decker"]However, I'd still like to get two boards that have the MSP Rev C parts.[/quote] If you now order the MSP-EXP432P401R LaunchPad you will receive Rev. C parts on the red board.
View ArticleForum Post: RE: Place a program and it's variables in FRAM
That is correct, however Section 3.3 of SLAA628 gives several reasons as to why the stack should be placed in SRAM. Section 3.4 should also be reviewed carefully. Regards, Ryan
View ArticleForum Post: RE: MSP430FR5969 SPI UCAxTXBUF Question
After further investigation, the problem may be on the Master side with the Master not clearing out it's receive FIFO properly, which causes the data to look shifted. I will try to post a follow up to...
View ArticleForum Post: RE: PMBus slave implementation
Hi Toby, Thank you for looking at MSP for your solution. Regarding your questions: Devices with eUSCI can implement multiple addresses by using 4 address registers (UCBxI2COA0-UCBxI2COA3), and/or by...
View ArticleForum Post: RE: 800 spectral lines out of 1024 FFT outputs
The amplitude of the FFT result is directly correlated to the length of "real" samples (non-zero). In fact the definition of the FFT can be interpreted as the cross-correlation of an input signal with...
View ArticleForum Post: RE: MSP432 eUSCI_B3 confusion
JM. I would be careful of the 'wired-or' that takes place within the device. Specifically, if one of the devices tries to clock stretch the SCL line it is possible that the MSP432 (acting as the...
View ArticleForum Post: RE: When will EXP-MSP432P401R LaunchPads ship with MSP432P401R...
no worries that explains it
View ArticleForum Post: RTOS Analyzer did not show up under tools
Hi, We tried to set up the system analyzer in TI ROTS but it could not show up under the Tools menu. What we have done are: 1. Add the following line to the .cfg file var LoggingSetup =...
View ArticleForum Post: MSP430F5529 - I2C Master Read - Faulty Read R/W bit in certain cases
Hi, I'm communicating between MSP430F5529 and a DS2482 (1-Wire <> I2C device). Normal bus transactions work fine when I issue a WRITE command and then repeated start and read command, as per the...
View ArticleForum Post: RE: MSP430F2xx board "lockup" need JTAG reprogram to recover
Hi Katie, Nothing to report as yet, but testing is still going on as a background process -- the main issue being slow discharge of the battery. I will post a report once we have enough data. Thanks,...
View ArticleForum Post: RE: RTOS Analyzer did not show up under tools
Update: This is also the case when running the MSP432P401R Stairstep example. It's happening on both of our machines, and we're wondering if it is an issue with CCS for macOS, if there is a problem...
View ArticleForum Post: RE: MSP432 unable to program
Hi Eddy, Is there a way you could share you schematics? Best regards, David
View ArticleForum Post: RE: RTOS Analyzer did not show up under tools
Now we are able to see it show up in a Windows version of CCS v6. But it could not show up in the Mac version of CCS. Is there a way to reconfigure the TI RTOS to let the analyzer show up in Mac? Thanks!
View ArticleForum Post: How to increase C5535 on-chip bootloader UART baud rate?
Our system has 2 processors. The master processor is able to boot TI C5535eZdsp through UART. However, the C5535eZdsp bootloader sets up to receive data at UART baud rate of 57600. Loading DSP FW takes...
View ArticleForum Post: RE: MSP432P401R Launchpad, waking up from LPM3
AJ, You may also find this thread useful - e2e.ti.com/.../1947196 Regards, David
View ArticleForum Post: MSP430 device with 4 external timer clock inputs
I am looking for MSP430 device with 4(or more) external timer clock inputs. External timer clock input means TAxCLK or TBxCLK can be supplied from an external pin. I know MSP430F524x, F523x meet this...
View ArticleForum Post: RE: getting problem in implementing uart communication using...
yes m trying to see the output on pc hyperterminal and also on putty but there is no luck. here is my code #include int main(void) { WDTCTL = WDTPW + WDTHOLD; // Stop WDT P4SEL = BIT4+BIT5; // P4.4,5 =...
View Article