Forum Post: RE: Are pads H1 and G1 on MSP320FG6626 AVCC or DVCC?
You are right - there seems to be a mistake in either the package overview or in the table. Here is my opinion: Pin 16 of the PZ package and H1 / G2 of the ZQW package is AVCC, so the table is wrong....
View ArticleForum Post: RE: lcd 16*2 msp430f5529
The minimum delay times are given in the datasheet of the HD44780 controller.
View ArticleForum Post: RE: Software initiated interrupts on the msp430
The Intel 8051 is not able to invoke an interrupt via software. And if you are talking about x86: that register you mention, if it exists at all, is part of an external interrupt controller. On the...
View ArticleForum Post: RE: MSP430F5249: Power consumption in LPM0/1
Hi Wei, There was a mistake in previous question. Customer actually wants to know SMCLK 1MHz (clocked from DCO). Datasheet shows LPM0 with this configuration. What is the rough estimation for LPM1 ?...
View ArticleForum Post: RE: Need help interfacing MSP430F5529 to TI ADC128S022 octal ADC
Blindly changing UCCKPL and UCCKPH is not helpful; there is only one correct setting, and you have to understand which one it is. If in doubt, check with a logic analyzer. Section 7.3.1 of the...
View ArticleForum Post: DAC with DMA
Hi Does anybody have idea to drive DAC with DMA using msp430f6659 ...?
View ArticleForum Post: RE: Finding the base address of a timer module in the msp430f5438a
The header file defines symbols such as TIMER_A1_BASE.
View ArticleForum Post: RE: Noise on MSP430 UART in CCS Debugger
Thank you James, it turned out that the problem was in the hardware. The TDO/TDI was tied the enable bit on the UART device that I was interfacing with. Thus when the debugger ran, it would toggle the...
View ArticleForum Post: RE: Specification of timer mode in the msp430
The TIMER_A_initUpMode() function starts the timer only if the startTimer field is set.
View ArticleForum Post: RE: Wakeup time from LPM0 and LPM1
Oops, I confused the LDO and the SV* L performance modes. The mapping of low-power modes to performance modes is shown in section 2.2.9.1 of the User's Guide, and also depends on how the SVS/SVM are...
View ArticleForum Post: RE: Specification of timer mode in the msp430
Does that mean that after i call TIMER_A_initUpMode() (with startTimer being set to true), i must call TIMER_A_startCounter() ?
View ArticleForum Post: RE: Wakeup time from LPM0 and LPM1
KoT, the datatsheet does not specify them in such a case I recommend to trust the data in the migration guide. Best regards, Dietmar
View ArticleForum Post: RE: Global constructors in a C++ project with GCC on the MSP432
I have recompiled my minimal example with Linaro GCC which is bundled with Code Composer Studio 6.2. and the result is more or less the same. The code causes a usage fault in __libc_init_array() only...
View ArticleForum Post: RE: Specification of timer mode in the msp430
No; you need a separate call to start the timer only if you did not set startTimer .
View ArticleForum Post: RE: MSP432 Reset Voltage
Hi Bryan, my guess is, that the same voltages apply for the Reset pin as for the ordinary digital I/O ports (but I am not 100% sure). These are noted in the device specific data sheets, for the...
View ArticleForum Post: RE: Unable to use the msp430, communication problems I guess...
Hi, i had a similar issue (communication error) and tried to update the driver from the device manager. The message displayed was that the drivers were up to date. However, the problem still persists....
View ArticleForum Post: RE: Communication error in the msp430f5438a
Hi Rahul, Can you share a screenshot of the error message? Also, could you provide additional information about your setup? For example, your OS version, IAR version, debugger, custom or EVM or target...
View ArticleForum Post: RE: MSP432 revision C and red MSP432 Launchpad tools version...
Can I exchange a black MSP432 Launchpad for a red one with the updated silicon?
View ArticleForum Post: RE: MSP430F5435a - reset cause
Hello Antoine, On some other devices, a value of 0x1C in the SYSRSTIV register indicates a PLL unlock (PUC) reset. This does not make much sense seeing as how the MSP430F5435a does not have a USB...
View ArticleForum Post: RE: Msp430g2553 ADC clock division
Hi celeb ' I don't know how to thank you for that great support and your time. after your modification now i can read adc signal as the rang i expect . but for some reasons i can't read the full data...
View Article