Forum Post: RE: Compiler/MSP430F5328: SPI receive not working .....
Hi Neil, I'm looking into this for you. Can you check to see if your seeing anything on the lines with a oscilloscope or a a logic analyzer?
View ArticleForum Post: RE: CCS/MSP432P401R: Implement SPI on SPPDemo example
Hello, Which MSP432 are you using? I am assuming that you are using a launchpad. Please make sure that you have made the appropriate updates to support the latest revision (revision C, red launch pad)....
View ArticleForum Post: RE: MSP430G2553: MSP430 / MSP432 - external start...
Timo, I should mention that there are faster MSP's (25MHz) and MSP432 is 48MHz. Perhaps I am missing something, but could you not use a GPIO interrupt for step 1 to start a timer and set a timer...
View ArticleForum Post: RE: MSP-CAPT-FR2633: Captivate Design Center - Multi i2c slave...
HPL, Thanks for evaluating CapTIvate. The CapTIvate Design Center does not support multiple I2C bus addresses at this time. However, the HID-BRIDGE does and you can do a manual configuration to set it...
View ArticleForum Post: RE: CCS/MSP430G2553: I2C receive does not seem to work
Hi Abhinav What do you see in the buffer? Can you check the I2C lines to ensure you are getting a proper response from the device. The device Address can be found in the INA data sheet at...
View ArticleForum Post: MSP430F5438A: XT1 CLOCK with 32768Hz
Part Number: MSP430F5438A Hello, Do we need external capacitors to connect 32.768KHZ to XT1 points of MSP430F5438A controller? Please let me know.
View ArticleForum Post: RE: MSP432P401R: Issues with Qmath
Hi Shawn, I have reached out to the library author for comment. Regards, Chris
View ArticleForum Post: RE: MSP432P401R: msp432 dma impact on cpu cycles
[quote user="f. m."]P.S. You should check out the documentation for equivalent japanese products (like Renesas RX600 or Fujitsu/Spansion/Cypress MB9Bxx).[/quote] No, thanx. Everybody have it's...
View ArticleForum Post: RE: CCS/MSP430I2041: Load Program Error CCS 6.1.3 - MSP-FET430UIF
Cameron, I am trying to contact the Hardware Engineer or the layout consultant In the mean time, I am sending you a photo of the board, JP1 is the SBW connector, which is very close to micro pins 15...
View ArticleForum Post: RE: MSP432P401R: Please help to figure out the relationship...
So, if I understand correctly, the total time is (sampling time+1 cycle)+(conversion time+1 cycle). Thank you everybody and happy holidays!
View ArticleForum Post: MSP430F6765A: PIN.h, PIN_HYSTERESIS, and the buffer
Part Number: MSP430F6765A Where is the documentation that explains what pin hysteresis is? I'm looking at...
View ArticleForum Post: RE: CCS/MSP430F6659: DCO above 100Mhz
Leave it....... i will upgrade to DSP .
View ArticleForum Post: RE: MSP432P401R: msp432 dma impact on cpu cycles
Sounds like you know those already ... ;-) Anyway, time to turn to family business now. A Merry Christmas and a Happy New Year to everybody !
View ArticleForum Post: MSP430G2553: Devices to program MSP430G2553 via RS485...
Part Number: MSP430G2553 Hello, I have a project about MSP430G2553 and I want to program it via RS485 communication protocol. I will buy the necessary devices to program it but I want to be sure what I...
View ArticleForum Post: RE: MSP430G2553: Devices to program MSP430G2553 via RS485...
I have just noticed that MSP430G2553 can be programmed with JTAG and communicated with RS485 :) But I want to learn the devices to program and communicate with it. Thank you.
View ArticleForum Post: MSP432P401R: alignment errors from driverlib
Part Number: MSP432P401R The following throws an unaligned trap when used with Port 2 (and others). The reason is HWREG16 forces a ldrh instruction to be used which will fail if one has unaligned traps...
View ArticleForum Post: RE: CCS/MSP430G2553: I2C receive does not seem to work
Thanks for the reply Cameron! Regardless of the resistor I use or the slave address I give, the buffer shows 0x0200 in it. Also the buffer value is visible for some reason during code implementation....
View ArticleForum Post: RE: Interfacing MSP430G2553 with ADXL345 (I2C) and serial port...
Has anybody run into the condition where the red LED on the launchpad stays on constantly? No matter if the ADXL345 is connected or not the red LED is on all the time. I copied and pasted the code to...
View ArticleForum Post: MSP430F169: I2C Master Slave
Part Number: MSP430F169 Hello ...., I have used an example fet140_i2c_06.s43 MSP430F169 Master and fet140_i2c_07.s43 MSP430F169 Slave to test I2C Transfer. At my Oszilloscope I can see, the Master send...
View ArticleForum Post: MSP430F6765A: How to utilize PIN.h for MSP430, Board.h?
Part Number: MSP430F6765A I'm new to CCS but I'm learning quickly. I've got a great start on a RTOS project and have created proof of concepts for all my peripherals. Before I start the job of...
View Article