Forum Post: RE: captivate code size limit
Hi Nandish, It is possible to configure your project with the CapTIvate COMM module disabled, reducing the memory requirements for your design. The communications interface is controlled in the...
View ArticleForum Post: TI101 Interface issue with MSP430F2132
I have issue in communicating TMP101 with MSP430F2132 SDA is connected - P1.7 SCL is connected -P1.6 ADD0, ALERT pin are Grounded. the mcu is operated on external crystal 32.768Khz in LPM mode.
View ArticleForum Post: RE: emeter 6779 - CT phase calibration
Have you tried using the calibrator GUI from SLAA409? www.ti.com/.../slaa409a.pdf www.ti.com/.../slaa409a And here are some other threads involving EVM430-F6779 calibration: e2e.ti.com/.../1894288...
View ArticleForum Post: RE: MSP430F133 intermittently won't start and then does not reset
It appears that the MSP430F133 hardware may be in violation of the PUC/POR conditions stated in the device datasheet. VCC rise time must be greater than +1 V/ms and likewise the fall time should be...
View ArticleForum Post: RE: Unable to use MSP-FET as BSL tool for programming...
Nirmal, Your log file checks out and shows you programmed the device correctly. If the BSL scripter was unable to detect the MSP430 in BSL mode, or didn't receive correct acknowledgements from the BSL...
View ArticleForum Post: RE: Diagnosing SPI issue with MSP430FR4133 and DLP-7970ABP...
Hello Jonathan, It seems that the UCTXIFG is stuck at a value of zero to indicate that the UCB0TXBUF is not empty and therefore a new value should not be written to it. This contradicts the UCBUSY...
View ArticleForum Post: RE: MSP432 FAQ
Hey there, one little question: Is the MSP432P401R fully pin compatible with the XMS432P401R? I think so, but wanted to ask to be sure. best regards Benni
View ArticleForum Post: RE: UART configuration in msp430
If you want to cut a sheet of paper, you use a paper cutter to do it. But if you do not have that, you could fold the paper and tear it along the folding line. The former is "hardware", the later is...
View ArticleForum Post: RE: Using the ADC 8354 with the MSP432P401R : Problem
KBB, Yes, this has to do with the parity bit. Again, please check your initial SPI settings to make sure you set up the MSP432 in the way your slave device is expecting. Figure 23-4 in the technical...
View ArticleForum Post: RE: Trouble using MSP430 GCC
Hi Pascal, My version of the CCS new project creator gives me the option for MSPGCC so I'm guessing that the App Center's information is incorrect, which has happened to me before regarding MSPWare . I...
View ArticleForum Post: RE: UART configuration in msp430
Thanks for your reply. Please explain with any program
View ArticleForum Post: RE: MSP430F6731- error in power measurement for phase variation
Hello Pradhan, The schematic attached is of a very low quality, please include a higher resolution version. The input filtering shown is quite minimal for the amount of accuracy desired and should more...
View ArticleForum Post: RE: Flashing a Standalone 28-pin MSP430G2553 fails
Hi Dave, Thanks for letting us know that you found a solution to your issue! Regards, Ryan
View ArticleForum Post: RE: MSP430FR5736 and ADC10_B
Hi Al, No problem, glad to know that you've got it sorted out! Regards, Ryan
View ArticleForum Post: RE: MSP430i2040 Sub Metering EVM not reporting energy consumption...
Hi Ram, I do not know what specifically you are looking for but I do not think that GET_CONSUMPTION_PHASE_1 will give you the results you are looking for even if it is initialized properly. With the...
View ArticleForum Post: RE: TI101 Interface issue with MSP430F2132
Here's a blog post that you will find useful: e2e.ti.com/.../msp-i2c-getting-started-guide And here are some other threads you can reference: e2e.ti.com/.../711313 e2e.ti.com/.../588896 Regards, Ryan
View ArticleForum Post: RE: MSP430FR5869 Sawtooth Wave on ADC Sample
This is how unbuffered SAR ADC of msp430 works. Try to measure input voltage which is equal to VREF and you will see different kind of sawtooth. Sample capacitor have some residual charge after...
View ArticleForum Post: RE: DLMS COSEM - MSP430 - Error when reading more than 127 elements
Hello Alan, I would not state this as a bug but rather a limitation of the software, 128 elements is conveniently 2^7 and this maximum number of elements allowed could have something to do with the...
View ArticleForum Post: RE: MSP430FR5869 Sawtooth Wave on ADC Sample
Hello Akash! First, thank you for providing a very detailed scope shot and circuit. During sample time, an internal switch allows the input capacitance to be charged, which is reflected in the sawtooth...
View ArticleForum Post: RE: DLMS COSEM - MSP430 - TAG_DATE, TAG_TIME and TAG_DATETIME not...
Hello Alan, The only supported syntax listed in SLAA614 is ITEM_TAG_DATETIME_LP as part of an octet string with 11 other characters, have you tried using this yet? Regards, Ryan
View Article