Forum Post: RE: 4-wire SPI communication using RTOS on MSP432
Hi Vikram, Please take a look at this thread. e2e.ti.com/.../1956741 Regards, David
View ArticleForum Post: RE: 430Boost Sharp 96
Hi John, I think you meant spi instead of i2c. Please correct me if I'm wrong. Anyway, I put together the attached example code, it uses tiRTOS v2.16 and the 430BOOST SHARP96. (Please visit the site to...
View ArticleForum Post: RE: I2C MSP430FR6989 Launchpad Communication (PLEASE HELP!)
The pins cannot "just hover", the pullup resistors would prevent this (if they are actually connected to those pins). The code looks OK. To check whether the pins might have been damaged, configure...
View ArticleForum Post: RE: 4-wire SPI communication using RTOS on MSP432
Hi David, I went through the document earlier but when I implement it does not work at all. Although the master is able to transfer as I see the status of the transferOK flag to be positive nothing is...
View ArticleForum Post: RE: 430Boost Sharp 96
I mean I2C AND SPI are both being used in my application , SPI only for the LCD. And they both work fine with the 96x96 display, that is obsolete BTW. Your code does not use the 128 x 128 LCD. Did you...
View ArticleForum Post: RE: MSP432 Driving Parallel Display Interface
Hi David, Scott here, not Jacob. We're looking at something like the New Haven Display NHD-4.3-480272EF-ATXL-T (or similar), WQVGA 480x272, 4.3" diagonal, with resistive touch screen interface. Has a...
View ArticleForum Post: RE: MSP432 can't connect JTAG on MSP432P401R REV.C
Hi David, Customer totally build 300 sets PCBA, and 15pcs failure. Some of these failure device maybe can programm again, but others failure were never been programmed successed. Thanks!
View ArticleForum Post: RE: MSP-Gang not locking JTAG properly on FR6989?
Hi Phil, Thanks for posting - I am looking into this. I can confirm that using MSP430FR5969 and MSP-GANG I did Secure Device and the JTAG was locked from further access. However if I use BSL with the...
View ArticleForum Post: RE: MSP430F5132 Programming
Izham, I'm just checking to see if your having any luck with the other forum? They would indeed be your best source, since they are the owner of the evm.
View ArticleForum Post: RE: MSP432 ADC input buffer
Eddy, Can you please answer my questions above? Otherwise I will need to close this issue (I can reopen it if needed).
View ArticleForum Post: RE: MSP430F67651 Programming by Gang programmer
Hi Vikas, I'll go ahead and close this thread. If you hear back from the customer, we can continue our debug effort. Regards, James MSP Customer Applications
View ArticleForum Post: RE: Interrupt Driven I2C Design for Wii Nunchuck
Hello Jerry, What actual slave device are you connecting to? At what line does the code get stuck? Can you provide logic analyzer or oscilloscope screenshots that show a break in communication (NACK,...
View ArticleForum Post: RE: Multiplying MSP430FR5969 debugger problem
[quote user="Olli Mannisto"] Incidentally, fprintf to stderr is pretty slow. 300bps modem slow if that. Can I make it faster somehow? I know I can use printf if increase heap size etc but fprintf does...
View ArticleForum Post: RE: error in flashing MSP432P401R revison c
I had this same issue: I was repeatedly reprogramming the board while writing and debugging code in CCS6.2, and then one time it started showing this error. I fixed it by running the "Factory Reset...
View ArticleForum Post: MSP432, Error: 1063, Device ID is not recognized or is not...
I have the following error message when i try to upload the energia sketch onto my MSP432 device. fatal: CORTEX_M4_0: Error connecting to the target: (Error -1063 @ 0x0) Device ID is not recognized or...
View ArticleForum Post: XT2 / 3 frequency (50% duty cycle) on MSP430F5510 pin output
Few years ago my conclusion was that it is not possible to have frequency from XT2 (24 MHz) divided by 3 (8 MHz, 50% duty cycle) on ( MSP430F5510 ) port pin as output. Now, I am back to this topic...
View ArticleForum Post: RE: MSP432 baud in Energia
Energia does call other libraries. You might be able to debug "open loop" by search/grep through those libraries and finding a place set your desired UART speed. Another method would be to install Code...
View ArticleForum Post: RE: Initializing UART1 on MSP430F449...
Hello Denis, I did try the sample code by TI as you recommended. After executing the lines to set the UART1 I do not see the ME2 bits related to the UART1 get set . This code was executed on MSP430F449...
View ArticleForum Post: RE: MSP432, Error: 1063, Device ID is not recognized or is not...
Hi Janak, Please take a look at the following threads. If these recommendations don't fix your issue, please let us know. Also, is this an XMS432 (if so, Rev B or Rev C?) or an MSP432 device? Here are...
View ArticleForum Post: RE: MSP430 programmer
It sounds like you may be using the MSP-FET or our older MSP-FET430UIF debugger. These devices provide a convenient connection between a computer and an MSP430 microcontroller board for debugging...
View Article