Forum Post: Code Composer Studio Viewing Address entry
Hii I am new to code composer studio v5.5 I am using F28335 interfced with matlab. I am auto generating the code in matlab for a model (eQEP) and dumping it in ccs, Somehow i am not confident if the...
View ArticleForum Post: RE: UART continuous transmission of request bytes
Ryan, Thank you for the response. Since I'm targeting low power I want more advice regarding the UART communication. Suppose I have to send 3 bytes through uart to get the energy meter to respond and...
View ArticleForum Post: TMS37f158 UART example
Does anybody have a TMS37f158 MCU firmware based on MSP430f123 with a simple example just to test UART connection? This MCU is slightly different from MSP430f123 so the uart example codes provided by...
View ArticleForum Post: RE: MSP430 Changings configuration target gives me memory linker...
TI makes many different MSP430 chips for good reasons. You cannot arbitrarily replace one MSP430 with another MSP430 chip, slap on the same code for one chip and expect it to work on the other chips....
View ArticleForum Post: [MSP430FR5994] Confirm Release schedule
Hi TI Experts, Please let me confirm the following question. [Question] Would you please teach me the release schedule of MSP430FR5994 ? Especially, we are interested in small PKG. Best regards. Kaka
View ArticleForum Post: RE: MSP430G2955 Timer0_A3 loosing interrupts from TA0CCR2 when...
Jeff, I am looking into why the errata has not been already updated and published. This is what it should look like: I will update this post when the new errata is available. Regards, Chris
View ArticleForum Post: RE: MSP430G2955 Timer0_A3 loosing interrupts from TA0CCR2 when...
Thanks, Chris. Looks like about the same information after all. Will there be a compiler update so the compiler never generates CMP with TxIV? As in the OP's original code in C. Jeff
View ArticleForum Post: RE: MSP430G2955 Timer0_A3 loosing interrupts from TA0CCR2 when...
Jeff, I will need to investigate if and how the errata publishing will impact the release of a compiler update. I will give you an update by middle of next week with any update. Thanks and Regards, Chris
View ArticleForum Post: RE: MSP432 Maincode debugging with a Bootloader loaded
Did the recommendations above solve the issue? Regards, James MSP Customer Applications
View ArticleForum Post: RE: MSP430F5419 Bootloader question
Hi Paul, Were you able to figure out this issue? Regards, James MSP Customer Applications
View ArticleForum Post: RE: Need support for MSP432, GDB_AGENT, using msp-fet
Hi Eric, Not really sure why you can not use the XDS110, could you please give us more information on this?? I ran a few test using the xds110 that comes on the RED MSP432 LP and I was able to...
View ArticleForum Post: RE: High order THD calculation and Delta-type (3P3W) for 3-phase...
Hi Wayne, We are currently working with metering experts to answer this question and appreciate your patience while a response is formulated. Regards, Ryan
View ArticleForum Post: RE: High order THD calculation and Delta-type (3P3W) for 3-phase...
Wayne, 1. Please note that the EVM430-F6779 does not automatically support the THD. One has to use the same EVM, but overwrite the SW with the SW available on the TIDM-THDREADING TI Design, which is on...
View ArticleForum Post: RE: The Sharp ® Memory LCD BoosterPack and msp430g2553
Hello, Please refer to the MSP-EXP430G2 with Graphics Library Example Project which uses the 430BOOST-SHARP96 , available on MSPWare and here: www.ti.com/.../slac435 Regards, Ryan
View ArticleForum Post: RE: Getting started with the MSP-EXP430G2
Ryan, No improvement. I even went and deleted the entire contents of my TI folder. Tried to locate any MSP430 file and remove those. I then reinstalled CCS and updated. When I plug in the MSP-EXP430...
View ArticleForum Post: RE: CCS 6.1.3.00034 + MSP430-GCC 4_01_00_00 - uses MSP430X...
I can confirm that this issue is fixed in CCS v6.2.0.
View ArticleForum Post: RE: MSP430F5152 BSL Data Transmit Pin
Hi Katie Pier While you are at it please make them release the BSL source code for the MSP430F51x2 series in the CUSTOM-BSL430 package. Lot of thanks in advance.
View ArticleForum Post: RE: Need support for MSP432, GDB_AGENT, using msp-fet
Hi David, thanks for looking into this and trying your experiment. The XDS110 (which runs at 3.3V) connected to the JTAG pins on a 1.8V msp432p401x turns out will power the msp432 to 3 volts through...
View ArticleForum Post: RE: UART continuous transmission of request bytes
Ryan My transmit and receive signal is 3 bytes long. So is it okay to use polling till i send the byte in the transmit buffer? Could you also suggest an idea for how the transmit and receive interrupt...
View ArticleForum Post: RE: Need support for MSP432, GDB_AGENT, using msp-fet
Hi David, thanks for passing on the request up the chain. we'd prefer to stay with TI tools for our needs. So if TI did enhance gdb_agent to support the msp-fet with the msp432 cpus that would be most...
View Article